
ServicesMetal Roofing
Metal Roofing in New Palestine
We install standing seam and exposed-fastener steel roofs on your home with the same care for the details you never see. Panels are measured, cut and fastened with safe crew practices, and your yard is swept with a magnet before we leave.
A metal roof that suits your home and is installed safely
A metal roof is a long-term choice. Steel panels shed snow and rain well, stand up to wind, and keep their color for many years when the finish is chosen correctly. They also cost more up front than shingles, so we start with an honest look at whether metal makes sense for your home, your roof pitch and how long you plan to stay.
Safety shapes how we work. Metal is slippery when wet or frosted and panel edges are sharp, so our crews work tied off, handle panels with gloves, and keep a marked drop zone around the house. We tell you each morning which doors to use and where children and pets should stay clear.
If metal is not the best fit, we will say so and walk you through shingle roofing or a full roof replacement with asphalt instead.
What our metal roofing work includes
Deck inspection and repair
After tear-off we walk the bare deck and replace soft or delaminated sheathing. Metal panels lie flat only on a flat, solid surface, and a weak deck is the most common cause of waves and loose fasteners later.
High-temperature underlayment
Steel heats up fast in summer sun. We use a synthetic underlayment rated for that heat, with ice and water membrane at eaves and valleys where winter melt can back up.
Panel choice explained plainly
We show you standing seam with hidden clips and screw-down panels with exposed fasteners side by side. Standing seam lets the steel expand and contract freely; screw-down costs less but its washers need checking over the years.
Trim, flashing and ventilation
Ridge cap, eave and rake trim, and custom-bent flashing around chimneys and pipes are fitted to the profile of your panels. We also check intake and exhaust venting so moisture does not condense under the metal.
Snow guards over walkways
Snow slides off metal in sheets. Where it would land on a front step, a driveway or a lower roof, we recommend snow guards so the load lets go gradually.
Cleanup and magnet sweep
Metal trimmings and screws are collected daily. On the last day we run a rolling magnet over the lawn, beds and driveway.
Signs metal roofing may be the right call
Your shingles are near the end
Curling tabs, bare spots and granules in the gutters mean a replacement is coming. That is the natural moment to compare metal against another round of asphalt.
Repeated wind or hail repairs
If you have patched lifted shingles more than once, a fastened steel system may hold up better. We can also help with storm damage repair if the current roof needs attention first.
Ice dams along the eaves
Snow sheds from metal more readily, which reduces the buildup that forces meltwater under shingles. Ventilation and insulation still matter, and we check both.
An older metal roof showing rust
Rust at seams, loose screws or worn washers on an existing metal roof can sometimes be repaired. When panels are thin or corroded through, we will tell you plainly that it is time to replace.
You plan to stay for many years
Metal pays back over time. If you expect to remain in your home a long while, its lifespan becomes a real advantage.
How a metal roof installation runs
- 1
Free inspection and measurements
We look at the roof, attic and deck from above and below, take photos, and measure every plane. You get a written estimate with each line explained, plus a clear answer on whether metal suits your roof.
- 2
Permit and material order
We pull the permit where it is required and order panels cut to length for your roof. Lead times vary by color and profile, so we set a date once materials are confirmed.
- 3
Site setup and tear-off
We set up fall protection, tarp landscaping, and mark the drop zone. We strip only as much old roofing as we can dry in before the crew leaves each day, so the house stays covered through every night of the job.
- 4
Underlayment, panels and trim
Deck repairs, underlayment and flashing go down first, then panels are fastened to the spacing the manufacturer specifies. Trim and ridge cap finish each slope.
- 5
Final walk and cleanup
We walk the roof with you or send photos of every slope, then clear debris and sweep the property with a magnet.
What moves the cost of a metal roof
Every metal roof is priced from the measurements and condition we find during the inspection, so there are no guesses. Your written estimate lists panels, trim, underlayment, deck repair and labor separately. Financing is available if you would like to spread the cost.
- Panel system and gauge
- Standing seam with concealed clips costs more than screw-down panels. Thicker steel, such as 24 gauge over 26 or 29, adds to the price and resists dents better.
- Finish and color
- Premium paint systems hold color and resist chalking longer than basic finishes. Some colors also carry longer lead times.
- Roof shape and pitch
- Valleys, dormers, hips and skylights mean more cuts and more custom flashing. Steep slopes need extra safety setup and slow the work.
- Condition of the deck
- Soft or rotted sheathing must be replaced before panels go on. We photograph what we find and price replacement per sheet so you can see exactly what changed.
- Tear-off and extras
- The number of old layers, snow guards and any new gutters all affect the total, and each appears as its own line.
Metal roofing questions we hear often
Something not covered here? (317) 648-2777
Will rain sound louder on a steel roof than on shingles?
Very little, in most homes. The panels sit on solid sheathing with underlayment between them, and attic insulation absorbs much of the sound before it reaches your rooms. The drumming people picture comes from barns and sheds where metal is fastened to open framing with nothing underneath.
Does a metal roof attract lightning?
No. Lightning follows the tallest, most direct path to the ground, and the material on your roof does not change that. Steel is also noncombustible, so if a strike ever did happen, the roof itself would not catch fire.
Can metal go on top of the shingles I already have?
In some cases, when there is a single layer, the deck underneath is solid and local code permits it. We usually advise a full tear-off instead, because it lets us see and fix the sheathing. Sealing soft or rotted wood under new panels is not a shortcut we consider safe.
How does a metal roof hold up to hail?
Big hailstones can leave dents, and thinner panels show them more. A heavier gauge resists that better, and a dent seldom turns into a leak. We can compare gauges with you during the free inspection.
How many days will the installation take?
For most homes, a few working days after the materials are delivered. Roof size, pitch and the amount of deck repair all change the schedule. Rain or frost can also pause the job, since we keep crews off slick metal.

Talk through a metal roof for your home
We will inspect your roof, check the deck and attic, and give you a written estimate with an honest view on whether metal is the right fit.